Features
Two-message overlay capability per single section.
Countdown timer can be configured in several modes by user.
Requires 50 percent fewer section heads than incandescent-style signals.
Even illumination under any lighting conditions. No hot spots.
Exceptional message visibility and clarity.
Fits all standard signal heads.
Cost-efficient, layered message panel.
Easy to service.


1.0  General Description

1.1 Display Capabilities - One unit shall be capable of displaying the LED HAND/MAN
    legends and two (2) 7 segment digits, constructed of single rows of LED's.

1.2 Visibility - The legend shall be clearly legible, attracting attention under
    any lighting conditions from a distance of 200 feet anywhere within a 15-degree
    cone centered about the optical axis.
1.3  The signal shall consist of:
    a.  An LED module.
    b.  Protective backcover.
    c.  LED light source.
    d.  Power supply.

2.0 Countdown Timer Description

2.1 Microcontroller based, the user can set all modes and timing functions via
    a multiposition dip switch, and a dual digit thumbwheel switch. All system
    timing is derived from the MAN and  PED CLEAR/don't walk controller signal.

2.2 A counter/digits test button is also provided.

2.3 The Modes are described as follows:

2.3.1 Mode 1 - PED CLEAR MODE
    This mode counts down ONLY during the PED-CLEAR time. The count terminates
    at the end of PED-CLEAR time. The countdown timer continuously monitors the
    PED-CLEAR signal and automatically adjusts for any changes made at the controller.

2.3.2 Mode 2 - WALK/PED CLEAR MODE
    This mode begins countdown with the man signal and counts down until
    termination of PED-CLEAR time. The countdown timer continuously monitors
    the WALK/PED CLEAR signal and automatically adjusts for any changes made
    at the controller.

2.3.3 Other modes available upon request.

2.4 Test Switch: displays "88" for a 2 second  time period and goes out.

2.5 Dimming  (Optional) Factory set but is user adjustable. Set by board mounted
    adjustment.  Dimming delay is 20 seconds.

3.0  Functional Requirements

3.1 The "HAND" display is made of High Intensity (AllnGaP) LED's.

3.2 The "MAN" display is made of High Intensity (InGaN) LED's.

3.3 Digits display is made of High Intensity (AllnGaP) LED's.

3.4 LED's operate at 20 milliamps DC, typically

3.5 LED's are industry standard 100,000 hour MTBF devices.

3.6 Power per display will be less than 10 watts

3.7 Backcover for module - Protective backcover for the module will be provided to
    eliminate damage to the LED circuitry during installation.

3.8 Message color - The unit shall display proper color messages.
    Portland Orange for the "HAND" and the "TIMER". White for the "MAN".
    These colors shall be in conformance with ITE specifications.
3.9 HAND/MAN legends, TIMER digits and power supply are made of Solid State
    Circuitry.

3.10 Operating temperatures - The unit shall be capable of continuous operation over
     a temperature range of -35F to +165F (-37C to +75C).

3.11 Blank out - The signal shall completely blank out when not energized. No phantom
     legends shall be seen under any ambient light condition.

3.12 Lens - A matte/clear .125" polycarbonate lens shall be used over the LED module
    to prevent intrusion of foreign objects and to provide resistance to vandalism.

3.13 Hardware - All screws, washers, nuts and bolts shall be stainless steel, and all
     other components shall be corrosion-resistant. All components are readily
     accessible when the door is open.

4.0 Electrical Description

4.1 Maximum power consumption is 15W.

4.2 Power Requirement 120Vac 50/60 Hz.

4.3 Voltage surge protection to withstand transients as stated in NEMA TS2 standard.

4.4 Operation requires standard 3 wire connection.
    120Vac - HAND, 120Vac - MAN, 120Vac - RETURN, and case Ground.

5.0 Installation

5.1 Retrofit kits are easily installed in the field.

5.2 Kits available in 12" or 16" sizes.

Warranty
All products will be warranted to be free of defects due to material and
workmanship for a period of two (2) years.